联系我们
18560023440
王经理:18560023440
地址:山东省德州市齐河县经济开发区齐众大道7号-2车间
业内资讯
数控设备故障了怎么办?
来源:http://www.jmycnc.com 时间:2021-11-22
一。主轴自动转或停不了
One. The spindle can not rotate or stop automatically
控制卡故障;
Control card failure;
变频器故障
Inverter fault
二。打开软件时,电脑提示“打开卡失败,请检查卡”的提示
II. When opening the software, the computer prompts "failed to open the card, please check the card"
检查板卡的驱动程序有没有装好,或把板卡换一个PCI插槽;
Check whether the driver of the board is installed, or replace the board with a PCI slot;
把两根数据连接线重新安装,检查有没有断针的现象;
Reinstall the two data connecting wires and check whether the needle is broken;
板卡有问题,更换板卡
There is a problem with the board. Replace the board
三。打开软件时提示:三轴报警,初始化错误四号
Three. Prompt when opening the software: three axis alarm, initialization error No. 4
检查电脑与机器的两根数据线有没有接好;
Check whether the two data cables of the computer and the machine are connected properly;
检查控制箱内的转接板的保险丝是否烧掉,换保险丝;
Check whether the fuse of the adapter board in the control box is burnt out and replace the fuse;
检查85V电源是否正常供电
Check whether the 85V power supply supplies normally
四。雕刻时出现错位或尺寸不对
Four. Dislocation or wrong size during engraving
检查雕刻软件的路径正确与否;
Check whether the path of engraving software is correct;
检查丝杆的间隙大小及光杆的紧固螺丝有没有松动;
Check the clearance of the screw rod and whether the fastening screw of the polished rod is loose;
检查软件参数的设置正确
Check that the software parameters are set correctly
五。X轴行走某段时Z轴不抬刀,按向上走却向下走
Five. When the x-axis travels for a certain section, the z-axis does not lift the knife. Press up but down
检查Z轴马达是否正常运行,功率及驱动器电流的大小或自身故障;
Check whether the z-axis motor operates normally, the power and driver current or its own fault;
检查Z轴马达线是否有接触不良或中间断的情况
Check whether the z-axis motor line has poor contact or broken in the middle
六。主轴电机不转或反转
Six. Spindle motor does not rotate or reverses
查变频器的参数的设置;
Check the parameter setting of the frequency converter;
变频器的信号线是否接反
Is the signal line of the frequency converter connected reversely
七。出现砸刀现象
Seven. Knife smashing
轴马达功率不够,联轴器松动;
Insufficient power of shaft motor and loose coupling;
轴驱动器的电流过小,或信号线接错
The current of shaft driver is too small or the signal line is connected incorrectly
八。打开软件开机时,出现轴关闭
Eight. When the software is turned on, the shaft is closed
驱动器的问题或电脑输出信号线接触不良;
The problem of the driver or the poor contact of the computer output signal line;
马达线接触不良
Poor contact of motor wire
九。雕刻过程中出现限位现象
Nine. Limit during engraving
检查雕刻路径是否超过雕刻范围;
Check whether the engraving path exceeds the engraving range;
在软件中参数设置的软限位
Soft limit of parameter setting in software
十。开机时机器不通电
Ten. The machine is not powered on when starting up
检查启动按钮线是否接好及按钮是否烧坏;
Check whether the start button line is connected properly and whether the button is burnt out;
检查交流接触器是否短路或烧坏
Check whether the AC contactor is short circuited or burnt out
十一。按钮运动时轴只往一个方向走
Eleven. When the button moves, the axis only goes in one direction
检查光藕线是否正常工作及其线路是否接触好;
Check whether the optical coupling line works normally and whether the line is in good contact;
检查电机线路是否有虚焊
Check the motor circuit for faulty welding
十二。发送软件不能正常打开,雕刻的东西出现畸形
Twelve. The sending software cannot be opened normally, and the carved things are deformed
重新安装新系统及软件;
Reinstall the new system and software;
检查X,Y轴丝杆及螺丝是否松动;
Check whether the screw rods and screws of X and Y axes are loose;
雕刻刀具有问题
There is a problem with the engraving tool
十三。雕刻机工作过程中主轴电机突然停转或转慢
Thirteen. When the engraving machine is working, the spindle motor suddenly stops or slows down
工作电压不稳或超负载,加个稳压器即可;
If the working voltage is unstable or overloaded, add a voltage regulator;
检查中间线是否接好,线头是否有脱焊。
Check whether the intermediate wire is connected properly and whether the wire head is desoldered.
十四。雕刻机设置原点时有时向前。向右偏移距离不定
Fourteen. The engraving machine sometimes moves forward when setting the origin. The offset distance to the right is variable
限位开关失灵,在系统回到系统原点的过程中限位开关已闭合又弹开。换限位开关即可;
The limit switch fails. When the system returns to the system origin, the limit switch has been closed and bounced open. Change the limit switch;
驱动线松动。设法把其固定紧即可。
Loose drive line. Try to fix it tightly.
十五。雕刻机启动复位时为可X轴。Y轴。Z轴位置不定
Fifteen. When the engraving machine is started and reset, it can be x-axis. Y axis. Z-axis position is uncertain
限位开关坏(限位开关始终闭合),换之即可;
If the limit switch is broken (the limit switch is always closed), replace it;
驱动线坏(X轴14针与15针短路,Y轴13针与15针短路,Z轴31针与15针短路),换驱动线或把短路处分开即可;
The drive line is broken (short circuit between pin 14 and pin 15 of X axis, short circuit between pin 13 and pin 15 of Y axis, and short circuit between pin 31 and pin 15 of Z axis). Replace the drive line or remove the short circuit;
驱动板坏,换驱动板即可。
If the drive board is broken, replace the drive board.
以上精彩内容由五轴保丽龙雕刻机提供,更多资讯请关注http://www.jmycnc.com/
The above highlights are provided by the five axis poly dragon engraving machine. Please pay attention to more information http://www.jmycnc.com/
- 上一篇:开料时开料机跑板的原因
- 下一篇:玉石雕刻机主要应用范围