欢迎光临山东墨源数控设备有限公司官网为您提供:保丽龙雕刻机,五轴保丽龙刻机,四轴保丽龙雕刻机

济南光纤切割机,济南木工加工中心,保丽龙加工中心
NEWSCENTER
新闻资讯
联系我们

18560023440

王经理:18560023440
地址:山东省德州市齐河县经济开发区齐众大道7号-2车间

新闻资讯 当前位置:首页 - 新闻中心 > 新闻资讯 >

如何通过雕刻机主轴电机声音判断故障

来源:http://www.jmycnc.com 时间:2021-06-18 

主轴电机在工作时由于旋转摩擦会发出一些声音,正常工作的主轴声音比较平和没有多少杂音,如果发现主轴电机的声音不正常就需要对主轴进行检修了。
When the spindle motor is working, it will make some noise due to the rotating friction. The sound of the normal working spindle is relatively flat and there is not much noise. If the sound of the spindle motor is abnormal, it is necessary to overhaul the spindle.
由于五轴保丽龙雕刻机主轴电机长时间高频率的运转,再者使用不当,主轴很容易出现一些噪音,但是一般的使用客户们很难通过声音来判断主轴电机的具体问题。今天济南凸凹机械在这给大家分析下,主轴电机的声音不正常有哪些情况,希望大家可以对自己的主轴进行及时的保养。
Due to the engraving machine spindle motor long time high frequency operation, and improper use, the spindle is prone to some noise, but the general use of customers are difficult to judge the specific problems of the spindle motor through the sound. Today, Jinan convex concave machinery in this analysis for you, the sound of the spindle motor is abnormal, what are the circumstances, I hope you can timely maintenance of their own spindle.
五轴保丽龙雕刻机
1、哒哒的声音:声音频率随轴承转速而变化,零件表面波纹度是引起噪音的主要原因。解决方法:改善轴承滚道表面加工质量,降低波纹度幅值、减少碰伤、修正游隙预紧力和配合,检查自由端轴承的运转,改善轴与轴承座的精度安装方法。
1. Dada sound: the sound frequency changes with the bearing speed, and the surface waviness of parts is the main cause of noise. Solutions: improve the surface processing quality of the bearing raceway, reduce the amplitude of waviness, reduce the impact, correct the clearance preload and fit, check the operation of the free end bearing, and improve the precision installation method of the shaft and bearing seat.
2、嗡嗡的声音:马达无负荷运转是发出类似蜂鸣一样的声音,且马达发生轴向异常振动,开或关机时有嗡嗡声。解决方法:多出现在润滑状态不好,以及在冬天且两端用球轴承的马达,主要是轴调心性能不好时,轴向振动影响下产生的一种不稳定的振动.
2. Buzzing sound: when the motor runs without load, it makes a sound similar to a beep, and the motor has abnormal axial vibration, and there is a buzzing sound when it is turned on or off. Solution: it often occurs in the motor with poor lubrication and ball bearings at both ends in winter, which is mainly a kind of unstable vibration under the influence of axial vibration when the shaft alignment performance is not good
3、杂质音:由轴承或优质的清洁度引起,发出一种不规则的异常音,声音时有时无,时大时小,在高速电机上发生频繁。解决方法:选用好的油脂、提高注脂前的清洁度、加强轴承的密封性能、提高安装环境的清洁度
3. Impurity sound: it is caused by the bearing or high-quality cleanliness, and makes a kind of irregular abnormal sound. The sound is sometimes non-existent, sometimes large and sometimes small, which occurs frequently in high-speed motors. Solutions: select good grease, improve the cleanliness before grease injection, strengthen the sealing performance of bearing, and improve the cleanliness of installation environment
4、淅沥淅沥的声音:由保持器与滚动体振动、冲撞产生,不管润滑脂种类如何都可能产生,承受力矩、负荷或径向游隙大的时候更容易产生.解决方法:提高保持器精度、选用游隙小的轴承或对轴承施加预负荷、降低力矩负荷,减少安装误差、选用好的油脂。
4. Rustling sound: it is produced by the vibration and collision between retainer and rolling element, no matter what kind of grease is, and it is easier to produce when bearing torque, load or radial clearance is large. Solutions: improve the accuracy of retainer, select bearing with small clearance or preload bearing, reduce torque load, reduce installation error and select good grease.