欢迎光临山东墨源数控设备有限公司官网为您提供:保丽龙雕刻机,五轴保丽龙刻机,四轴保丽龙雕刻机

济南光纤切割机,济南木工加工中心,保丽龙加工中心
INFORMATION
业内资讯
联系我们

18560023440

王经理:18560023440
地址:山东省德州市齐河县经济开发区齐众大道7号-2车间

业内资讯 当前位置:首页 - 新闻中心 > 业内资讯 >

泡沫雕刻机日常维护相关步骤

来源:http://www.jmycnc.com 时间:2021-09-10 

泡沫雕刻机,本文的內容将再次为大伙儿叙述相关立体式泡沫雕刻机设备维护管理的相关流程,接下去一起访问文章内容,掌握相关内容!
Foam carving machine, the contents of this article will once again describe the related process of equipment maintenance and management for the three dimensional foam carving machine, and then visit the article content and grasp the related content.
1.定时执行清理电源电路箱的排热排风系统,请定期维护电气控制柜上的每个风扇工作是不是一切正常,按时用吸尘机清除一次电气控制柜里的尘土,查验接线端子排螺钉是不是松脱,以确保电源电路一切正常、靠谱应用。
1. Regularly clean the heat and air exhaust system of the power circuit box. Please regularly maintain whether each fan on the electrical control cabinet works normally, remove the dust in the electrical control cabinet with a vacuum cleaner on time, and check whether the screws of the wiring terminal block are loose, so as to ensure that the power circuit is normal and reliable.
2.应尽量避免开电气控制柜的门,严禁开关门工作中,在手工雕刻时空气中一般都是有尘土、木渣或金属粉,一旦他们落在电气控制柜内的线路板或电子元器件上,非常容易造成电子器件间接地电阻降低,乃至造成电子器件及线路板毁坏。
2. Try to avoid opening the door of the electrical control cabinet. It is strictly prohibited to open and close the door. In the process of manual engraving, there are generally dust, wood slag or metal powder in the air. Once they fall on the circuit board or electronic components in the electrical control cabinet, it is very easy to reduce the indirect resistance of electronic components and even destroy electronic components and circuit boards.
3.定期维护设备各构件螺丝是不是松脱。
3. Regularly maintain whether the screws of each component of the equipment are loose.
4.机械泵的维护保养:
4. Maintenance of mechanical pump:
A水循环系统打气泵呼吸口腔内部的金属丝网制品是用于避免外地人细颗粒物进到泵壳,此过滤网应随时随地保持干净,防止阻塞而造成泵的泵效降低,当离心水泵无需时应当每几日接电源运行数分钟,避免泵身长锈没法一切正常运行。
A the metal mesh products inside the breathing cavity of the air pump of the water circulation system are used to avoid the fine particles from outsiders from entering the pump shell. The filter screen should be kept clean anytime and anywhere to prevent the blockage from reducing the pump efficiency. When the centrifugal pump is not needed, it should be connected to the power supply every few days and run for several minutes to prevent the pump body from rusting and unable to operate normally.
B一般机械泵也应当松掉蝶形螺母,取下纸质过滤芯按时用髙压汽体清除滤网,发觉过滤芯换气不如意或毁坏,应立即拆换,依据使用时间长度能用髙压加油枪给各处滚动轴承上油。
B for general mechanical pumps, the butterfly nut shall also be loosened, the paper filter element shall be removed, and the filter screen shall be removed with high-pressure steam on time. If the filter element is found to be unsatisfactory or damaged, it shall be removed and replaced immediately, and the high-pressure refueling gun can be used to oil all rolling bearings according to the length of service time.
5.严苛依照使用说明书实际操作及遵循应用标准。
5. Strictly follow the actual operation in accordance with the operating instructions and the application standards.
以上内容就是为大伙儿详细介绍的相关立体式泡沫雕刻机维护保养的流程相关内容,数控雕刻机与人一样也是有性命的,要想数控雕刻机各构件自始至终保持稳定的情况,坚持不懈常常的维修保养是十分关键的。那样能够把许多常见故障安全隐患解决在萌芽期情况,避免特发常见故障产生。实际操作工作人员应当培养常常对应用机器设备开展维护保养的良好的习惯!
Unremittingly, the above contents are related to the maintenance process of the three-dimensional foam carving machine for everyone. CNC carving machines are also like human beings. If we want to keep the components of CNC engraving machine from first to last, we must persist in maintaining and maintaining the key. In that way, many common faults and potential safety hazards can be solved in the embryonic stage to avoid special common faults. The actual operation staff should cultivate the good habit of often carrying out maintenance on the application machinery and equipment!